The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.

Why does my chainsaw start but not stay running?

The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.

How do you fix a chainsaw that won't idle?

1. Make Sure Choke is Off.
2. Air Filter Clogged.
3. Bad Gas.
4. Fuel Line and/or Filter Clogged.
5. Fouled Spark Plug.
6. Primer Bulb is Clogged or Leaking.
7. Idle Ports are Clogged.
8. High/Low Screws and Adjustment Idle Screw Needs Calibrating.

Why does my chainsaw shut off when I give it gas?

Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle. … If the filter becomes clogged, not enough fuel will reach the engine for it to run properly.

How do I keep my chainsaw running?

1. Keep your Chain Sharp: Keeping your chain sharp is probably the easiest and most effective way to extend the life of your saw. …
2. Flip your Bar: …
3. Drain your Gas: …
4. Check your Sprocket: …
5. Keep a watchful Eye:

Why does my Stihl chainsaw bog down when I give it gas?

The Job of the Carburetor Without the right amount of air and fuel in the piston cylinder, the 2-cycle engine in a Stihl chain saw runs inefficiently and the saw loses power. … When the saw bogs down during cutting, it’s usually the high-speed screw you need to adjust.

How do you clean a chainsaw fuel filter?

Brush the air filter gently with a soft brush or wash it in warm soapy water then dry it. Do not use compressed air to clean it – compressed air can blow holes in the filter, allowing dust and debris into your carburetor.

What happens if spark arrestor is clogged?

Sometimes the spark arrestor screen can become clogged up itself. Common symptoms include lack of power, especially under load; poor acceleration; engine won’t come up to full RPM; and higher than normal “spit back” through the carburetor.

Is seafoam good for chainsaws?

At Sea Foam, we recommend overcoming saw starting issues by adding 2–4 ounces of Sea Foam Motor Treatment to a low tank of fuel, running it for about five minutes, then letting it sit a night or two to soak or clean. Add fresh fuel and proper two-stroke oil before operating and it’ll be good to go.

Is it OK to remove spark arrestor?

You can safely remove the spark arrestor or even install an aftermarket exhaust system on many ATVs without having to make alterations to your jetting because they are normally set up to run a bit rich from the factory, but this is no general rule!

Article first time published on

What does a spark arrestor do on a chainsaw?

The spark arrestor on your chainsaw prevents dangerous hot sparks from igniting fires while you’re working. If the arrestor is clogged or dirty, however, it will also prevent exhaust from leaving the motor, which can prevent it from running.

How do I know if my fuel filter is clogged?

1. Trouble Starting the Engine. The most common sign of a clogged fuel filter is trouble starting the car, since it depletes the oil supply going to the engine. …
2. Issues Accelerating. …
3. Frequent Idling and Sputtering. …
4. Strong Odors. …
5. Engine Misfires/Low Performance. …
6. When to Replace the Fuel Filter.

How do I know if my chainsaw fuel filter is bad?

1. Poor Engine Performance.
2. Hard Starting.
3. Stalling.
4. Random Misfire or Rough Idle.
5. Fuel System Part Failures.

What do the high and low screws do on a chainsaw?

Most Pro Saw Engines Have Three Carburetor Adjusting Screws: If this adjustment is set too high, the high idle speed will cause the centrifugal clutch to engage and the chain will run. … Low Speed Fuel Adjustment – This is the adjustment that controls the proportion of fuel in the air/fuel mixture at idle speed.

How tight should a chainsaw chain be?

A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can’t pull the drive links out of the bar nose.

What is the H and L on a carburetor?

They are typically labeled L (low speed jet), H (high speed jet), and I (idler jet).

What does the T stand for on a chainsaw?

The letters on the screws represent High (H), Low (L) and Idle (T). The H screw regulates the Air/Fuel mix during high RPMs, while the L Screw does the same during low RPMs. The T screw regulates how much fuel is sent to the carburettor while idling until the throttle is pressed.

Can you clean a chainsaw carburetor without taking it apart?

You can clean the outside of the carb without disassembly but the important stuff to clean is on the inside and for that it must be disassembled. There was a time when you could buy good quality carb cleaner to soak your disassembled carb in to clean all of the passages but not any longer.

Can seafoam clean a carburetor?

Use Sea Foam Spray to safely and effectively clean residues and deposits from intake valves, chambers and compression rings! Sea Foam Spray delivers a high concentration of petroleum cleaning solvency and lubricity to carburetor throttle valves, intake runners and valves, and chamber areas.

Do all chainsaws have spark arrestors?

Chainsaw manufacturers include a spark arrestor on every model to prevent combustion byproducts from escaping the combustion chamber during saw operation and starting a fire. … To access the spark arrestor, you’ll probably have to remove the muffler.

Do Stihl chainsaws have spark arrestor?

Spark Arrester Muffler has large baffles which reduce noise level and contain a screen designed to reduce the emission of sparks. STIHL Quickstop® Chain Brake System is designed to stop the chain in fractions of a second. Can be manually activated or activated by inertia if the kickback force is sufficient.

Is spark arrestor necessary?

A properly maintained turbocharged engine does not need a spark arrester. Superchargers do not use the exhaust gas but are directly coupled to the engine. Engines equipped with superchargers require a spark arrester.