Unlike a standard flange, which is centered on the waste pipe, an offset flange is off-center—that lets you shift the location of the toilet by a couple of inches (left, right, forward or back).

How many inches does an offset toilet flange move?

The typical offset is 12-inches for most residential toilets.

How do I know if my toilet is a 10 or 12 rough?

If the old toilet is still there, measure from the center of the capped bolts (on the bottom) to the wall (not the baseboard). There should be 24 inches of clearance from the wall facing the bowl and 15 inches on each side as a guideline. If your measurements are between 11.5 and 12.5 inches, it is a 12-inch rough-in.

How do you install an offset toilet flange in concrete?

1. Cut off the Old Flange and Obstructions. After you remove the toilet, you will probably find an existing toilet flange. …
2. Scrape off Old Wax Ring. …
3. Pick the Correct New Toilet Flange. …
4. Place T-Bolts in New Toilet Flange. …
5. Position Toilet Flange. …
6. Drill Holes Into Concrete. …
7. Screw Toilet Flange Onto Concrete.

Is it possible to move a toilet a few inches?

Yes, you can actually move a toilet. Even moving a toilet by a few inches without having to make a new hole in the floor is possible. You can use an offset toilet flange to move the toilet by a couple of inches on any side. This will allow you to use the same wastewater line and in turn help to save you a lot of money.

How much does it cost to relocate a toilet?

The cost to move a toilet or sinks can be $2,500-$3,500 per fixture. Plumbing can be a significant cost factor in a remodel when a bathroom floor plan is altered. The toilet is the most expensive to move. Connecting the toilet to the existing sewer line can be a bit tricky for your plumber.

Can I move my toilet 6 inches?

To move the toilet more than just a couple of inches, you will have to demolish the concrete to access and relocate water and waste lines. Then you will have to rebuild the concrete foundation and replace the sub-flooring, flooring, and fixtures.

Can a toilet flange be too high?

When your toilet flange is too high, your toilet may leak water and rock back and forth when used. Both the leaking and the rocking can warp or break the floor. A leaking flange can also rot the subfloor and lead to the accumulation of mildew and mold.

Can you replace a 10 inch rough in toilet with a 12 inch rough in toilet?

The rough-in for your bathroom plumbing should match the rough-in for the toilet. Even if a toilet is designed for a 10-inch rough-in, you can still install it in a space with a 12-inch rough-in.

Does a toilet flange need to be screwed to the floor?

The flange should be fastened to the floor. Dry fit the toilet to make sure it doesn’t rock. If it does rock, use shims to prevent rocking – just tightening the bolts probably will not stop the rocking but will risk cracking the toilet or breaking the flange.

Article first time published on

What is the elbow neck on a toilet?

Width – Measure the bottom of your toilet. To determine the correct width for your wax ring, simply turn your toilet bowl on its side, and measure the opening on the bottom of your toilet, called the “elbow neck.” Whatever width this measurement is, use that width wax ring.

Does the toilet flange have to be flush with the floor?

5 Answers. The toilet flange needs to be on top of the finished floor. Meaning the bottom edge of the flange needs to be on the same plane as the toilet. So if your toilet sits on the tile, the flange needs to be on top of the tile too.

How is toilet offset measured?

Measure from the wall behind the toilet to the center of one of the closet bolts (which hold the toilet down). If the toilet has four closet bolts, measure to the center of one of the rear ones. Then measure from the center of the mounting holes to the back of the new toilet you’re considering.

Can a toilet be more than 12 inches from the wall?

It won’t affect how the toilet itself operates. However, the extra inches will cause the tank to be further away from the shutoff valve on the wall, so a longer connector may be needed to reach effectively.

Why would I want an elongated toilet bowl?

Elongated bowls are also considered more ‘hygienic’ in that the larger surface area of the bowl makes is easier for men and children to use with less mess. The longer bowl size is also a requirement for ADA use, and the longer/wider bowl is generally easier to use for those with mobility issues.

Can you move a toilet to where a shower was?

Can you put a toilet where a shower was? The simple answer is yes, you can put a toilet where a shower was, but the move doesn’t come without its issues. This isn’t a simple DIY job. You are going to have to remove at least one wall and, hopefully, only a small portion of the floor.

How far is toilet flange from wall?

The Distance To Set The Toilet Flange From The Back Wall. You’ll want to set the center of the water closet flange 12 inches from the finished back wall. Don’t measure from the base molding!

How far can a soil pipe run?

longest run for horizontal soil is 6 metres, but what about when u add bends.

Can you move a toilet UK?

Moving a toilet is not a straightforward weekend DIY job, but it is very doable when you involve the professionals. Once the toilet itself is removed, your plumber will have to move the drainage, as well as the water supply to accommodate the new location.

What is a toilet stack?

Q: What is a stack in plumbing? A: A “stack” is described as the vertical section of a plumbing drainage system of soil, waste or vent piping rising through one or more stories of a building. The stack is the largest vertical pipe into which all the horizontal pipes either drain or vent.

Is moving plumbing expensive?

On average, it costs somewhere between $500-$1,000 to move a plumbing fixture around three feet or more. This varies, of course, depending on if your plumber needs to move anything around to connect to your drain, vent, or water lines.

What does 12 rough-in for toilet mean?

The toilet rough-in refers to the distance from the finished wall to the center of the toilet’s floor drain or waste outlet. Most toilets have a rough-in of 12 inches, although it’s not uncommon for older homes to have an unusual size such as 10″ or 14″. … Rear-outlet toilets are configured a bit differently.

What measurements do you need to replace a toilet?

Make sure you measure from the centre of the bolts, up to the drywall (as opposed to the baseboard). If there are four bolt caps, be sure to measure from the center of the rear set. Toilets come in 10”, 14”, and most commonly, 12” rough-in dimensions.

How do you measure a toilet rough-in without a toilet?

To measure the rough-in for your toilet, measure from the wall behind the toilet to the middle of the bolt caps (the caps holding your toilet to the floor). If there are four bolt caps, measure to the rear set of bolt caps.

What is the right height for a toilet flange?

The optimum flange height to aim for is 1/4 inch above the finished floor. This typically allows for almost any type of wax ring to be used and still ensure a good seal.

What do you do if the toilet flange is above the floor?

Cut it so that your pipe is flush with the floor. Many floors are not properly square, so you’ll need to check what the angle of the floor happens to be to create the flush cut. Then attach the new flange. If your toilet flange is too high, do not use the toilet until you’ve corrected the problem.

Why does my toilet rock when I sit?

Toilets usually rock because they are not resting flush against the floor. Underneath the toilet base is a round toilet flange that connects the toilet to the drain pipe. If the flange is a little higher than the surrounding flooring, the toilet becomes raised slightly in the center, allowing it to rock to either side.

How much does a plumber charge to replace a toilet flange?

The cost for a plumber to replace the toilet flange varies by region and service provider, but the average price range is approximately $130 to $310.

Is toilet flange glued to pipe?

If the pipe has a 4-inch inside diameter: This toilet flange is designed to glue on the inside of the pipe or expand inside the pipe. Leave the old toilet flange right in place and glue on the new one at the right elevation for the floor, if it’s plastic. … If it isn’t, then you will have to cut away the old flange.

Should I use a wax ring with a flange?

The wax ring with a sleeve often called a deep seal bowl wax, is a very reliable seal for a toilet although it can be messy. … If you have a normal height closet flange then you can use the regular wax ring with a sleeve. If your flange is floor level or slightly below then you can use an extra-thick wax ring.

What kind of wax is used for toilet rings?

Some seals are made from beeswax, but others are constructed from petroleum or other ingredients. The material that the wax ring on your toilet is made from depends on who manufactured it. Regardless, this kind of seal is pliable and a reliable way to seal between the toilet bowl and flange.