Traditional flue pipe replacement costs range from $400 to more than $800, especially if you have an older type of unit. If you have an older, less efficient unit, your flue pipe replacement costs will be much more than modern units. Your furnace needs to vent exhaust outside as part of its combustion.

How much does it cost to replace a furnace flue pipe?

Your furnace uses flue pipes to exhaust gases outside your home. The average cost to repair or replace a flue pipe is $400–$800.

How much is a flue pipe?

Depending on accessibility and the overall length, a flue pipe costs $400-$800. Carbon monoxide and leftover gases are carried out of your home by the flue.

How do you replace a flue pipe?

1. Look over the section of flue pipe you want to replace. …
2. Unscrew the sheet metal screws from the section of flue pipe you wish to replace. …
3. Measure the length of the flue pipe and prepare a replacement piece by cutting a piece of flue pipe to the correct length using your snips.

What is a flue pipe on a furnace?

The flue pipe is a duct pipe that vents, or exhausts, gases from inside the home to the outside. A byproduct of combustion contains carbon monoxide and other dangerous compounds.

Does a furnace flue need to be cleaned?

A flue that is unable to properly vent can become filled with dangerous, and even deadly vapors that will eventually leak right back into your home. Therefore, it is essential that you have your flue inspected and properly cleaned at least once a year.

How do I know if my furnace flue is clogged?

Signs of Clogged Flues If you see rust or water streaking on the vent, flue, or on your chimney, something may be blocking the flue. Moisture builds inside your furnace pipes when the air can’t properly circulate, and this can result in rust. Soot around your furnace is also an indication of a problem.

What is a chimney pipe?

A chimney pipe is a tube made from one or more types of metal, used to ventilate the exhaust and smoke from your chimney to the safety of the outdoors. Some exhaust systems are installed straight up through the chimney, where they vent out through the roof.

How do you size a flue pipe?

To determine the main flue size, refer to Figure 3 and locate the square inch area of each individual flue size. Next, total the square inch areas and refer back to Figure 3 to determine the pipe size the total corresponds with. In our example, 78.54 square inches equal a 10″ pipe size.

How much is pipe for wood stove?

A wood stove pipe costs $100 to $550 on average, depending on the length and design. Costs are higher for cathedral ceiling installations since more stovepipe is required. A stovepipe is the internal ventilation pipe that connects the stove to a nearby chimney.

Article first time published on

How high does a stove pipe have to be over the roof?

In essence, any chimney, stove pipe or other heating exhaust vent should be 3 feet (1 meter) above the roofline or 2 feet (61 centimeters) above any part of the building in a 10-foot (3-meter) radius.

Where is the furnace flue pipe located?

These types of furnaces usually have a flue pipe that goes up through the roof of your house, since the combustion byproducts are gases. They easily float up through the flue and out of the house.

How do you inspect a flue pipe?

1. Remove the flue cap to check for blockages such as debris or birds’ nests.
2. Replace and secure the cap tightly to the end of the flue pipe. …
3. Look for signs of blockages by examining the pipe itself – water streaks or rust on the flue pipe may indicate a blockage, causing moisture to back up.

How do you remove the furnace flue pipe?

Access the furnace through the door on the furnace closet. Loosen the clamp where the lower end of the vent attaches to the furnace using the screwdriver or nut driver. Pull off the end of the pipe from the flange. Tap the pipe with the hammer, if necessary, to dislodge it and pull it off the flange.

What happens if there is improper venting of the furnace?

Combustion byproducts, such as carbon monoxide, can lead to many ill effects. This includes headaches, dizziness, nausea, fatigue, and even death. When your furnace has a blockage or backdraft and cannot properly vent, combustion gases cannot escape.

What happens when a furnace vent is blocked?

If the exhaust flue is blocked, the inducer fan won’t move any air, and the pressure switch won’t trigger. The furnace won’t proceed to heat until the pressure switch is triggered. This is to ensure that your furnace has enough airflow for complete combustion and to remove gaseous byproducts from your home.

How often should furnace flue be cleaned?

The National Fire Protection Assoc. 211 codes state that “chimneys must be inspected and cleaned if needed annually” – just like the oil service man services the furnace annually, so should the chimney system be serviced annually.

How often should you clean furnace chimney?

The National Fire Protection Association 211 states that chimneys shall be “inspected annually and cleaned and repaired if needed”. Just as the oil furnace is serviced annually, so should your chimney system be serviced annually by a CSIA Certified Chimney Sweep®.

Do you need a chimney with gas heat?

Most homeowners are aware of the need for chimney cleaning and inspection if they own a wood-burning stove or regularly use their fireplace. But many don’t realize that a gas heating appliance – whether it is a furnace, boiler or even a water heater – relies on the chimney for proper venting of the exhaust.

How much does it cost to install chimney?

Chimney Installation CostNational average cost$6,500Average range$4,000 – $8,000Minimum cost$3,500Maximum cost$11,500

How long does it take to install a flue?

A flexible liner can generally be fitted within one day, a twin wall system can take one or two days and a pumice lining system can take 4 or 5 days.

Can I complain about my Neighbours wood burning stove?

Local Councils are legally obliged to investigate complaints made under the Environmental Protection Act 1990 relating to public health and nuisance issues, which include smoke and fumes from fires or stoves.

How long do flue liners last?

Average Lifespan of Chimney Liners The average lifespan of a chimney liner is 15 to 20 years. After two decades you will probably need to get the entire liner replaced to make sure it’s still up to code and not a serious fire risk.

Who is responsible for shared chimney?

And the answer is simple: if the chimney is on the party wall, then the party wall act applies. This is usually the case, because at least one side of the flue is usually on the party wall, and, in some cases, the chimney itself can overlap and become shared in the loft spaces of the two properties.

How do I know what size flue I need?

In general, flue size should be 25 percent larger than the size of the stove pipe, which connects the stove to the chimney. This means a stove with a 6-inch diameter pipe would require at least an 8-inch flue; an 8-inch stove pipe requires a 10-inch flue, etc.

What is the difference between a flue and a vent?

Vents may exit vertically through the top of the roof or horizontally through a wall. Some may even run through a chimney, as long as anything else venting through the space is contained in a separate flue. Vents help remove the byproducts from combustion just like chimneys and flues.

Does my chimney have a flue?

Technically, a flue is any open vertical space in a chimney that allows smoke to escape the home from the firebox. But because every chimney’s flue must be lined, a chimney liner is usually referred to as the flue, as well. Every wood-burning or gas fireplace has a flue.

Why is it called a flue?

Historically the term flue meant the chimney itself. In the United States, they are also known as vents for boilers and as breeching for water heaters and modern furnaces. They usually operate by buoyancy, also known as the stack effect, or the combustion products may be ‘induced’ via a blower.

What is a stovepipe leg?

Stovepipe pants. Basically, a slightly tighter version of straight-leg pants, this style is fitted to the knee, then falls straight to the ankle. Stovepipe pants work for inverted triangles; they hit at the lower hips, which will add a bit of weight there to balance a strong shoulder.

How much does it cost to have a wood burning fireplace insert installed?

Most fireplace inserts and a professional installation cost about $2,000 to $4,000, depending on the state of your existing chimney and the model you select.

Can a wood stove chimney go out the wall?

If you’re setting up a wood-burning stove or pellet stove, running the chimney pipe through an outside wall saves the time and costs of installing a vertical chimney that requires a ceiling collar and roof flashing. … For brick or stone walls, enlist a professional to cut the holes.