If your cables are looking fine, try unplugging the fan for a few minutes and then plugging it back in again. Sometimes, this process can reset the motor and solve your furnace problems. If unplugging and plugging your fan back in again doesn’t work, check the fuse box.

How do I know if my furnace blower motor is bad?

1. Poor or Airflow from Air Vents. This will be the first and most obvious sign your blower motor has a problem. …
2. No Airflow At All From Vents. …
3. Skyrocketing Energy Bills. …
4. Strange Noises When You Turn on the Heat. …
5. Overheating Blower / Weird Smells.

Do all furnace blower motors have a reset button?

All furnaces are equipped with a reset button. They are generally red or yellow and are located inside the blower compartment. The reset button is a safety feature that will shut down the furnace when a problem is detected, often a hot or overheating furnace, before it trips the circuit breaker.

How do you reset furnace blower?

1. Step 1: Turn off the power to the furnace. …
2. Step 2: Remove the blower compartment cover. …
3. Step 3: Make sure the blower is completely cooled off. …
4. Step 4: Locate the reset button. …
5. Step 5: Press the button in (assuming that this is your issue and that the button has popped).

What can cause a blower motor to stop working?

In most cases, a blower motor resistor fails due to corrosion or overheating. Sometimes, the mechanical resistance to the motor rotation causes an excessive electric current that can overheat and prematurely damage the blower motor resistor.

What happens when your blower motor goes out?

A bad blower motor can cause a lack of air flow from the vents when the heating or air conditioning is on. The system won’t function if the blower motor burns out or short circuits.

What happens when blower motor goes bad?

You might also hear ongoing whirring noises, or noises that change or get louder if you increase the fan speed. These are all signs of problems with the blower motor. In some cases, you may even notice smoke or smells of burning while driving, in which case you should pull over immediately.

Why is my heat not blowing hot air?

Heater Not Blowing Warm Air Because of Thermostat Settings. Make sure you check the thermostat which controls your HVAC system. … If your thermostat takes batteries, check and replace them if necessary. If your thermostat is set correctly and your heater is still not coming on, you may have a faulty thermostat.

Where is the reset button on a blower motor?

Examine the exposed components in the furnace cabinet to locate the blower motor; look for a small silver box positioned toward the top of the cabinet. Mounted just above this box you should see a small round component with a raised red or white button at the center; this is the blower reset switch.

Why will a blower run on the on position and not on auto?

Other Blower Fan Won’t Run Problems The fan will run and blow warm air but only in FAN or FAN ON mode – delivering heat – but NOT in AUTO mode. This is a bad temperature sensor in the unit; replace the fan limit controller.

Article first time published on

Should I hit the reset button on my furnace?

The purpose of the reset button on a furnace is to shut it down before it can trip your circuit breaker. The need for this may arise if the furnace becomes too hot, or if there is some sort of electrical system interruption. To get the furnace working again, you simply press the reset button back down again.

Can you fix a blower motor?

There are a number of things that can go wrong with your heating system, but if the air stops blowing altogether and the same is true on cold air settings, a blower motor replacement is likely in order. The good news is that it’s a fairly straight forward repair.

How much does it cost to replace a blower motor on a furnace?

On average nationwide, a furnace blower motor replacement costs $400-$600, including parts and labor. A single-speed blower motor costs around $450 to replace while a variable-speed motor costs $600+.

How much does it cost to fix a blower motor?

Cost to Replace Central or Forced Air Blower Motor Replacing a blower motor costs $450 on average with a typical range of $250 to $800. With a warranty, you might pay as little as $150 for labor alone. For high-end models, like those with large motors or access issues, you might pay as much as $2,000.

How do I know if my fan motor is bad?

1. The fan won’t start even though the AC is on.
2. The fan won’t stop, even when you shut the AC off.
3. The fan turns on, yet the blades are rotating very slowly.
4. There’s a rattling noise coming from the condenser unit when the fan is turned on.

How do I get my furnace to kick on?

1. Check your circuit breakers.
2. Check your thermostat settings.
3. Ensure your furnace filters are clean.
4. Check your pilot light.
5. Check your blower motor.
6. Check the furnace ignition switch.

Why is my furnace lit but not blowing hot air?

These conditions are most often caused by thermostats and filters. Make sure that airflow into your furnace is not blocked or limited. If the furnace heats up just fine but continuously blows even when it is not putting out warm air there can be a problem with your limit switch.

Why is my furnace blowing cold air instead of heat?

Your furnace may be blowing cold air because the filter is too dirty. A dirty air filter blocks airflow over the furnace’s heat exchanger, causing it to overheat. When overheating, your furnace can trip a high limit switch, causing the furnace burners to shut off so that the heat exchanger does not crack.

Why is my furnace running but not blowing air?

Your filter could be so saturated with dust and debris. … Every modern furnace is equipped with a safety shutoff that will be tripped if your furnace gets too hot, and a clogged air filter can cause your furnace to overheat, shut itself off and give you the illusion of a furnace not blowing air.

Why is my air handler not coming on?

First make sure there is power to the indoor unit and that a switch or breaker isn’t off. Some indoor units (Heat Pumps) have breakers right on the Air Handler itself. … Some units have a shutoff switch on the side of the unit or an Emergency Switch located on a wall. Then make sure your air filter isn’t blocked.

Should you turn fan on with heat?

Keeping your fan on AUTO is the most energy-efficient option. The fan only runs when the system is on and not continuously. There is better dehumidification in your home during the summer months. When your fan is set to AUTO, moisture from cold cooling coils can drip and be drained outside.

Why is my central heat not working on auto?

Two of the most common reasons your home central heating isn’t working are a dirty flame sensor and a dirty air filter. Clean the flame sensor with a steel wool pad and replace the air filter every 1-2 months. This will help prevent future problems.

How do you reset a furnace after overheating?

1. Turn down the thermostat to its lowest setting.
2. At the circuit breaker, turn off the power to the furnace.
3. If this is a gas furnace, turn off the gas supply at the valve for the main gas pipe, but leave the pilot’s gas supply on.
4. If the pilot light was out, light a match to relight it.

How much is a blower resistor?

The average cost to replace the blower motor resistor at a repair shop is between $44 and $55 in parts and $70 in labor costs, for a total cost of around $114 to $125.