In almost every case, the answer is yes, you can lay down a new metal roof over an existing shingle roof. This is one of the many reasons metal roofs keep growing in popularity – their installation doesn’t require completely tearing off the existing roof, which is a time-consuming and expensive job.

Can you put metal roofing directly over shingles?

In almost every case, the answer is yes, you can lay down a new metal roof over an existing shingle roof. This is one of the many reasons metal roofs keep growing in popularity – their installation doesn’t require completely tearing off the existing roof, which is a time-consuming and expensive job.

Do you need purlins for metal roof over shingles?

The metal will be attached to at least 3/4″ purlin and 1/2″ plywood instead of just 1/2″ plywood, which should make the overall roofing system stronger. But probably the best benefit that comes from using purlins is the air gap it creates between the metal roof and the existing shingle roof.

Do I need underlayment for metal roof over shingles?

Underlayment is not required when installing metal roofing over shingles but is a definite plus. This extra layer ensures the previous shingles are not under continued stress which could lead to an increased risk of roof damage.

Do you need strapping under metal roofing?

Single wood strapping is better than no strapping, as it creates a wider gap between the existing roof decking and the metal roof, but doesn’t afford enough ventilation to resolve condensation issues. It also does not allow leveling of the roof, which corrects swells and swales on the roof.

Can I install a metal roof myself?

Metal roofing systems that you can install yourself are readily available, but you need to feel comfortable working with metal (and you’ll pay a pretty steep price). The only specialty tool you’ll need is a locking sheet metal tool (available at roofing suppliers or online).

How do you attach a metal carport roof to a shingle roof?

1. Hold the end of a chalk line at one of the outermost, top corners of the carport roof frame. …
2. Snap a chalk line between the two transition marks on the shingle roof. …
3. Remove two courses of shingles above the chalk line with a cleanup scraper.

What is the best underlayment for a metal roof?

Felt Underlayment (Asphalt Felt/Tar Paper Underlayment) Known by many different names (including felt paper, roofing tar paper, and asphalt-soaked felt), felt underlayment is the most commonly used type of underlayment material on steep-slope metal roofs.

Can you install metal roof without furring strips?

When installing a metal roof over an existing roof, insulate the spaces between the wood strips with rigid insulation to prevent condensation before installing the roofing. You also need to add furring strips. … Twenty-four inches is a common spacing of furring strips for a metal roof.

Can you put rolled roofing over shingles?

Q: Can I install roll roofing over shingles? Yes. The reason is simple: both roll roofing and shingles are a composition of the same asphalt material.

Article first time published on

How do you attach shingles to an existing roof?

The easiest way to tie in the new shingles with the old is with a cut valley (see Four Ways to Shingle a Valley). After the addition roof is framed and sheathed, snap a line on the existing roof shingles 2 in. up from the valley center, and cut through the shingles and underlayment.

How hard is it to put a metal roof on?

While most metal roofing styles can be installed as an advanced DIY project, metal roofing installation is complicated and can vary slightly based on the brand of panels or shingles that you select. We recommend that you install a metal roof with one or two helpers and fall protection equipment designed for roof work.

Is it easier to install a metal roof or shingle roof?

Shingle roofing is easier to install than metal roofing. This means that you have more contractor options for your work order. Many contractors have experience with shingles, so you can feel safe in finding a qualified professional quickly.

Do you put anything under metal roofing?

The simple answer is yes, your roof does need an underlayment. … If your home is built with joists, insulation between those joists, and sheathing, then an underlayment is needed before you put on a metal roof.

What goes under a standing seam metal roof?

Underlayment is usually a felt (15 lb, 30 lb, or synthetic) material used over your decking to provide additional protection. That makes it a crucial component to your metal roof. For your standing seam metal roof, your underlayment will be a self-adhering, high heat ice and water shield.

Which is better shingles or roll roofing?

Rolled MSR roofing is thinner, larger, cheaper, less durable, and is horizontally installed in long strips. Besides being thicker, composite shingles or any type of shingle are far less prone to tearing or cracking because stress is distributed across a wide area of individually moving parts.

How many layers of shingles can you put on a roof?

Most building codes allow up to two layers of organic or fiberglass asphalt shingles. That limit pertains to roofs with up to a 4:12 pitch. When it’s time to replace your roof, there are several factors that might lead your roofing professional to recommend adding shingles on top of your existing layers.

Can I put a second layer of shingles on my roof?

The short answer is yes, you can lay new roof shingles over the old ones. … You can’t do it with wood or metal, for example, and you should never mix materials, such as laying asphalt shingles over cedar shakes. Also, the old roofing has to be in pretty good shape.

Can I install a standing seam metal roof myself?

Although in theory, you can install standing seam metal roof over your existing asphalt shingle roof, I would advice you to tear off the old roof before installing standing seam due to a common effect of telegraphing of lines of asphalt shingles underneath the standing seam metal roof roof.

What is the screw spacing on a metal roof?

Lap screws are spaced 12” to 18” on center. The panel screws are spaced out so that every third corrugation has a screw including both sides of the panel sidelap.

How much should a metal roof overhang?

3: The panels at the eave side of the roof should overhang into the gutters 1 to 1-1/2 inches. If installing metal on a non gutter application you can overhang the panel up to 3 inches.